NV 300E

NV 10E

Another important features:
In order to prevent the output signals and display itself from constantly flickering, a hysteresis zone can be defined, within which any movement is not reflected in the display nor in the state of the outputs.

• With control of up to six depth levels in the EDM process, activating a digital relay signal depending on the position reached.
• You can display the EDM axis continuously or just show the lowest position reached.
• Each EDM level can be independently associated with any of the axes displayed (except with the NV10E).
• The value of each level can be changed, even while within the EDM process, accessing the value directly from the keyboard.
• They offer electrode radius compensation, for X Y positioning, and electrode length compensation which can be changed during the EDM process.
• If the machine does not control all the EDM levels, the unused ones can be deactivated, so their positions cannot be changed and their corresponding outputs cannot be activated.
• During the EDM process, the signals can be left in a non-activated state for electrode calibration or replacement.
• There are four digital inputs, used as Emergency Input and for resetting the axes.

NV 10E

NV 20E

NV 300E

• They have four digital inputs, used as Emergency input and for resetting the axes.
• It is possible to control the grinding levels on the vertical axis and travel limits on the other axes.
• The grinding axis can be displayed continuously or only display the lowest position reached.
• The wheel dressing operation can automatically be compensated,., as two feedback axes can be combined into a single axis display (except with the NV 10E).
• The value of each level can be changed, even while within the grinding process, accessing the value directly from the keyboard.
• If the machine does not use all the operating levels, these can be deactivated.
• While grinding, the signals can be left in a non-active state, so that electrode can be calibrated or replaced.
• It is possible to operate in radius or diameter, independently for each axis.

NV 20

NV 300T

NVP 300TRS

For Lathes
NV series for 2 to 3 axes

The very top quality and technology for increasing the productivity of your LATHE, guaranteeing the greatest profitability

• Ergonomic and easy to use.
• Study aluminum body.
• Reliable thanks to their advanced design and production technology.
• Fitted with a universal power supply to protect them from changes in voltage, power micro-surges and on-line noise.
• Complying with the most demanding standards, with CE certificate
• All NV models feature the following functions :-
  - Presetting.
  - Axis coupling.
  - Feedback reading maintained with the DRO off; DISPLAY OFF- mode.
  - Speed and feedback alarms, data safety storage in EEPROM.
  - Absolute and/or incremental counting per axis.

There are also NVP 300T programmable models, with program cycles:

• Turning cycles.
• Facing cycles.
• Position cycles.
• Teach-In.
• Tool Presetting.
• Chamfers (even in arcs).
• Calculation of Constant Surface Speed CSS and RPM.
  Programming assistance tool changes and tool compensation.
  Etc.

NV 20

NV 300M

NVP 300MRS
NVP 400MRS

All NV models feature the following functions:

• Presetting.
• Axis coupling.
• Feedback reading maintained with the DRO off; DISPLAY OFF-mode.
• Speed and feedback alarms, data safety storage in EEPROM.
• Absolute and/or incremental counting per axis.
• Shrinking factor (for operating with molds).
• Table sag compensation, ect.
• Bolt-hole calculation.
• Tool radius compensation.

There are also NVP 300 and NVP 400 programmable models, withprogramming cycles:

• Drills in rectangular or circular grid patterns.
• Rectangular pockets.
• With advanced features: scaling/mirror factor, tool change , series and probe Interface, multipoint compensation.
• Powerful and easy to use through their LD display and painstakingly designed interface in 6 languages, which makes communication with the operator easier,
  Etc.